How to Make a Dog Food Dispenser

How to Make a Dog Food Dispenser


thank you to simply safe for sponsoring
today’s video I’ll tell you about them later on
man it is crazy how fast time flies it was five years ago that I started making
YouTube video showing people how I was building things and one of those things
was the dog food dispenser it was just a simple shape and at the bottom I placed
a blast gate to release food into a pouring container it worked great but
there was no way to regulate how much dog food was being dispensed well in
this video I will show you how I remade the dispenser with a mechanism inside
that releases a set amount of food per pull of a lever pretty cool huh
let me start at the beginning and show you how I did it okay let’s start with
making the body I kept the overall shape of it the same
as before because honestly the shape is the best for the application I think but
this time I wanted to soften the shape some by adding in some curves instead of
messing around with bending wood I cut out a template on my C and C then traced
it onto a sheet of plywood and then cut it out what I’m doing is I’m building up
the sides to the height needed by stacking identical parts on top of each
other I’m using tight bonds fast drawing thick and quick here and also using a
brad nailer to hold the parts to the previous one for the body I’m using a
construction grade plywood because I’ll be painting mine later on if you would
rather stain yours and you can do the same process from any solid wood as well
but once the glue is dry I gave both sides of good sanding with 80 grit to
smooth out any slight unevenness between the layers if you use plywood unless you
use a really high-end grade there’s always gonna be a few voids in the plies
my method for filling these in for a seamless paint surface is to apply some
joint compound to it once the compound is fully dry I again
but with this time with 120 grit alright for the moment that is the body done so
let’s start working on the mechanism my little dogs eat one cup of food each day
so I started off building a mechanism that would dispense that amount I grab
some PVC pipe and cut two links at the miter saw this is what will store the
needed amount of food next I grab some half-inch scraps and started making a
few circles I used a compass to draw the circle a
bandsaw to cut them out then a Forstner bit to cut out these smaller needed
circles if you don’t have a Forstner bit you can instead use a drill to punch a
through hole large enough to get a jigsaw blade into then you can use a
jigsaw to cut it out this whole assembly creates the inside portion that holds
the food and also rotates about when the lever is pulled now to make the top and
bottom parts that will open and close off the holes and stay stationary while
the inside moves I’m again using scraps to make these parts and started off
cutting a few rectangles over at the table saw then I clamped them to my
armor tool table once again and punched a few holes in one of the plates after
the two holes were cut out I used two jig salts he cut a curved pathway
between the two this simple cutout drastically cuts down on the food
getting stuck and crunch when moving the lever and cutting off the flow of food
after drilling yet another circle on what will be the bottom you know where
the food drops out from I piled all the parts on top of each other and drilled a
center hole I started with the top assembly which has a circle cut out and
two square pieces being held together with the carriage bolt and two nuts to
lock it into place also on this assembly is something to
aggregate the food which in my case is a paint stirrer stick cut to length this
part will knock the food around when moving the lever to keep it flowing
nicely into the pipes below next I flipped it over and started assembling
the bottom first attaching the circle with two cutouts oh and I again use
tight bonds thick and quick to glue the PVC pipes to the wood this is an
interior multi-surface glue so it’s perfect for sticking different material
together quickly then lastly after you’re on the bottom
rectangle where the food drops out of and tightened everything down all right
now let me see if I can show you how it works when I attach the lever I’ll be
able to rotate the inside circles to one side which opens up one of the pipes
while closing the other this is the top so one will always be filling while the
other one will be closed then on the other side which will be the bottom
there’s only one hole and one pipe will always be empty while the other one is
closed off this closed off pipe is the one filling in theory you can resize the
device to hold any amount of dog food cat food cereal coffee beans really
anything you can think of but keep in mind the larger in diameter you go with
those pipes the larger the dispenser will be overall after putting this one
together I actually downsized mine because while
my dogs eat one cup of food daily they eat it over two meals throughout the day
so next I made it a device to dispense just half a cup of food at one time and
just going from a full cup to half a cup you can see the size difference that it
makes in the device which like I said will determine how big the body needs to
be before setting that aside to build the front the last thing I did was stick
a handle on it I made a simple shape then again use some tight bond to attach
it to the device itself okay and now onto the face remember that this can be
as simple as a plywood sheet but I thought it would be really cool to do a
two-piece live-edge with some epoxy down the middle that could be used as a sight
glass to see the level of dog food inside even cooler I am using a piece of
Mesquite I personally milled up myself a year ago with my chainsaw mill it just
so happened to be the perfect height for this project and was actually wide
enough to use as well but I thought it would be much cooler piece if I cut it
down the middle resold it to book match and point the two live edge portions
towards one another I used my track saw to rip down the
center but even doing this and exceeded the cut capacity of my bandsaw to resaw
it so I took it to my neighbor shop and used his to get two boards that are
about 3/8 of thik I quickly ran each one over the
jointer to get one side flat and then through my thickness planer to get the
second side flat real quick I want to pause and say a big thank you to this
video sponsor which is simply safe if you’ve been following along you know
that I’ve been using simply safe as my shop security for a while now it is
incredibly effective reliable home or shop security that will make sure your
property is safe at a price of only 50 cents a day I can relax no in my shop
and my tools are professionally monitored 24/7 and if anything happens
don’t make sure the police are called simply say system is modern
comprehensive and protects your property inside and out their professional
monitoring has 3.5 times faster police dispatch by security specialists who
provide real eyewitness evidence to the police department recently I decided to
take my shop security one step further and add the simply safe walk I can grant
access remotely if necessary and I can even set up unique access code so I can
get alerted as to exactly who is locking and unlocking the door simply say so
reliable comprehensive coverage at a value is one of the reasons experts call
it the number one recommended home security right now simply save us having
the biggest sale of the season protect your home and family this holiday season
with simply safe but hurry because the offer in cyber monday if you’d like to
learn more about someplace safe you can click the link down in the description
next I set up a station to do my epoxy pour first figuring out how my boards
were going to lay and how far apart they needed to be next I lay down tape to
cover up the bottom of the board and the intention here is to create a surface
that the epoxy won’t be able to stick to however I will tell you that this
painters tape ended up sticking really bad I hear house wrap tape releases much
better but I didn’t have any of that on hand after the tape I cut a few scraps
to link to create some walls these will build a form around my two mesquite
boards to keep the epoxy in I can use tape on the bottom edges of these boards
since they will be the portion in contact with the epoxy next I attach the
boards and sealed around it to prevent the epoxy from leaking out while it
dries I’ve seen people use silicone before but that has a really long dry
time and I was trying to get the pour done that day so I used a faceting
adhesive from tight bond called tight grab I laid down a decent bead under the
sidewalls and then mush them down on top it is an
adhesive so this will attach the walls to the bottom and then I just took these
squeezed out and used it to seal off where the bottom meets the walls and the
corners where the walls meet each other with the form done next I set my boards
in place then started to mix together the epoxy since my goal is to use this
as a site glass it’s really important to use an epoxy that would end up crystal
clear and this brand total boat has always amazed me on how clear it comes
out so that is what I use also if you’re needing epoxy remember that you can use
the code Apryl W to get 20% off anything total boat okay and time to pour I was a
little bit nervous because this was my first big ish epoxy pour but honestly
there was no reason to be I poured it right down the center until it filled up
to the surface then waited a little bit for it to settle and then kept pouring
in more you’ll see that there are lots of bug holes in the SAP wood of this
Mesquite I didn’t want these to get filled in
because I think they look cool as little tunnels
once you’re done pouring you can use a quick amount of flame to pop all of the
air bubbles in the epoxy then I recommend checking to make sure your
form isn’t leaking and then just let it sit until cured the next day I used a
mallet to bust open the form and expose the pour the sides did come off easily
enough but that tape that was stuck pretty darn good instead of spending the
time that would take to peel it off I ended up sanding it off which isn’t a
big problem since the next step was to sand the front and clean up all of the
excess epoxy for this job I started with 80 grit and I used the more aggressive
setting on my 6-inch Triton RS and this make quick work of the epoxy and the
tape I use my RS to go through the grits I have pads for which I only keep up to
320 in my shop so then I switched over to hand sanding and continued to 500-800
thousand fifteen hundred and then three thousand the goal is to remove all of
the scratches you made from the previous grid and after getting through three
thousand the last steps who really make it shine is to add some polish compound
and buff it you can do this a few different ways but I have a grinding
wheel that has a buffing wheel on one side so that’s what I use to polish up
the epoxy this was kind of hard to do because its side and its middle
placement but I made it work on both the front and back okay now that’s three components done
the body the mechanism in the front so now we can join them together the front
is really the main part that will be seen because my dispenser will end up in
my kitchen pantry so I picked out a brown that would complement the mesquite
wood then for the mechanism I painted it whatever sort of brown I had in a rattle
can I honestly didn’t think too much about it because you really can’t see it
as the sightglass narrows where it is after attaching the body to the
dispenser I set it on a piece of ply to trace out forward back
I quickly zip that out and then attached it using thick and quick once again for
lid I cut a piece of piano hinge to size and threw it on using a few short screws
before attaching the top I first squared up the top edge over at the table saw
using a crosscut sled once I had that edge sorted I measured down in two
different places to the final length I needed the piece and this way I could
use a track saw to cut it square okay so far so good
next I use the table saw to rip off another small strip of the epoxy pour to
attach it right underneath the handle after squaring both pieces up to the
body and also making sure they were in line with each other
I used the smallest girl that I own to punch through the front face and end to
the body my intention is to attach this face by using dowels but I don’t want to
see them on the front at all and I’m calling them blind dowels but I really
don’t know if that’s a real term or not after punching a few holes through the
face and into the body now I could remove the top and have an exact
location in both pieces to enlarge that would fit a dowel I used a piece of tape
on my drill bit to mark a depth and make sure I wouldn’t go through the face I
threw some type on and some quarter-inch dowels in the holes then cross my
fingers and hope this method work I don’t want to use a brad nailer on the
face so I threw it in clams until this glue is dried but then I used my
favorite bit which is that infinity mega flush trim bit to match the shape of the
body to the front I also used the Infinity round over bit after the soften
it it’s had by getting rid of those hard 90-degree edges then I ran over the
entire front with 220 grit paper all right and now on to finish this is my
first time working with Mesquite but what a beautiful beautiful wood not only
the red brownish of that heartwood but also that brilliant yellow SAP wood I
also love that the majority of the bug holes stayed hollow after letting three
coach dry I hung it up now this will end up in my kitchen pantry but since I
can’t easily get a camera in there I’ll hung it on my shop wall to show you how
it works dog food will go in at the top then
whenever I pull the lever a set amount will dispense from the bottom of course
whenever I’m serving the dogs I will place their food bowls under the
dispenser but for testing purposes I was using a measuring cup so what do you all
think I honestly wasn’t too sure about that live-edge front when I started but
I am really loving the way that it came out I think the sight glass is neat and
I love being able to just pull a lever and the right amount of food fall into
the bowl I hope that you enjoyed this project I hope that you learned
something and I will see you on my next project

100 comments

  1. Protect your shop, home and family this holiday season with SimpliSafe! Check out their Cyber Monday sale: https://simplisafe.com/April

  2. I really like your channel, you know how to work very well with wood and do very cool things! I always follow your work. Congratulations aprill and much success in your life! 😀👏😘

  3. Mesquite is a multi purpose wood smoking and wood working. I didn't realize the trees got that big I thought they were bushes.

  4. Great build April, amazing to see how you've progressed over the years. I remember your "I've quit my job and I'm going to be a builder full time" video like it was just yesterday. Way to go!

  5. Chainsaw mill!?? You did such a wonderful job building that awesome bandsaw mill. I suppose those boards were cut a while back.
    Anyway, your craftsmanship, as always, is fabulous. I enjoy all your videos, keep up the great work.

  6. Mount it lower on the wall; big bags of dog food get heavy. Then make the lever spring loaded so you can push it with your foot and dispense the food into the dog bowl.

  7. Outstanding, may have to do that too, the only thing may become a issue is the wood may dry the dog food more, great look too.

  8. This is really cool. I thought you had an ingenious way to line up the blind dowels, check out “dowel centers” next time then you won’t have to drill the holes through the outside.

  9. That’s a great design, very clever. I love the live edge front on that and that mesquite is just beautiful. Not that I’m the safety police or anything, never have I ever claimed that roll for anything as I’ve done it to, but where was your respirator when you were using the table saw or the router lol. My wife gets after me about that if she happens to see me not using my respirator when I should be haha.

  10. I would need a wall full of them. One for Malted Milk balls. One for M&M's Peanut, almond, and plain.
    Great idea April.

  11. This is what I found:
    The wooden dowel rod used in woodworking applications is commonly cut into dowel pins, which are used to reinforce joints and support shelves and other components in cabinet making. Some woodworkers make their own dowel pins, while others purchase dowel pins precut to the required length and diameter.

    When dowels are glued into blind holes, a very common case in dowel-based joinery, there must be a path for air and excess glue to escape when the dowel is pressed into place.

  12. Que hermoso trabajo…que lindo poder aprender de una mujer tan creativa y capaz…te admiro..
    Muchas bendiciones 🤗🙏🏻

  13. Great Upgrade. As I. I know I can do projects I built better once I've gotten better at what I do. Calling Simpli Safe tomorrow.

  14. Since you are already "protecting your home and shop," I strongly suggest that you protect your lungs also…WEAR A MASK…Matt does!!!

  15. This is fantastic but I really think you spoilt the sides spraying it brown while using good wood and nice epoxy on the front, it's like using something ugly to accentuate something beautiful which is needless. The plywood sides are beautiful in itself, I really don't understand that. I've never come up with a mechanism like that either which is awesome and also Acts as a way to state whether the dogs eaten or not as he does trick my partner into a third helping sometimes haha. Of course he's never been fed in his life. I love the front and transparent practicality the epoxy does, a great project I'd love to do especially when I build my kitchen

  16. I think you're potentially poisoning your dogs. None of the materials used are food safe. This design will trap kibble that won't get rotated out and the interior coated in oils that will go rancid or worse. Kibble is not great food to begin with and improper storage won't improve it.

  17. April I hope you are making a lot of money off these companies cause there is more product place here than a Rap video LOL!

  18. It needs some sort of funnel in the bottom, these corners looks like perfect collection point of old food, and also big headache to clean. Also, lid seal and inside lining… Not quite sure that it got enough level of airtighness and moisture protection.

  19. I love some of the techniques you used. I don't need a dispenser but many cool things can be built using some of your methods.

  20. April You nailed it again. I wish you were my all around shop teacher. Creativity and Hey let's give it a try, it can be awesome. Nice job, it's beautiful. And awesome engineering.

  21. April, it is a beautiful and functional piece for your precious doggies! Have you tried using dowel alignment pins, aka dowel centers, before? It might help you avoid having to drill through the face next time.

  22. Hey April, check out the super simple project that I think you may be able to use. It’s called a ticking stick. https://youtu.be/Cd2LY857oTY

  23. Great job April that really came out nice. But I'm just curious I think research has indicated that if you let dogs free feed they actually will eat less I have a hopper with a door on the front that the dog can just push open with his nose and he can snack his his leisure and I guarantee you he eats a lot less cuz it's always available and it's not like it's a big Feeding Frenzy at a particular time of the day. Just my two cents they like that Hopper came out really nice good job as usual

  24. erm… is the wood food grade? 🤣

    inspiring work!
    anyway, would be awesome if the container shape actually follows tht curve of yellow sub wood.

  25. Is there a way to seal the wood on the inside with something that both won't leech into the dog food, but will also protect the wood from any moisture in the dog food?

  26. April, you have become my most watched YouTube site. I'm a 72 yr. Young woodworker. I love the way you tackle any project. That is your success. You move forward while the other guy is sitting at his bench wondering if he can build a chair.

  27. Where you had the tape stick, we used to pour hundreds of Cypress clocks in Florida with epoxy. We used old boards and drove nails completely through and then placed our Cypress on the nail boards. Put plastic sheeting under the nail boards to catch the run off. Use a small handheld propane torch over the top as soon as you pour to get rid of air bubbles. When dry the next day, turn over on a old piece of carpet and sand of the drips with a grinder.

  28. April, very cool project. I have 3 girls, and they all like to build. They can't wait for me to finish my CNC router, But, speaking of routers. You have a fantastic router in your shop, and I've seen that you pass up using it on pieces that are begging to be made on it. Jump in there. There is almost nothing you can't do on a CNC. I've been running CNCs for 40 years+ Have fun. You are a great inspiration to girls as well as the men out here with the way you go after projects. Keep it up.

Add a Comment

Your email address will not be published. Required fields are marked *